• Hello Guest, you do not yet have the necessary rights to see the contents of our FAQ articles. Register in our forum, briefly introduce yourself and your Zetor in words and pictures and actively participate in discussions in the forum, then you will automatically receive access to the specialist articles in the FAQ.

Search results for query: *

  • Users: sb
  • Order by date
  1. 8011 setting

    8011 setting

    Hi all . am rebuilding the engine on a long 910 same as a 8011 . What are the big end torque setting and the head bolts . and also the tappets . thanks
  2. 8045 backwards 4wd

    8045 backwards 4wd

    You need to pull for 4wd . I think you might have the cable to long . When in 2wd the knob shud be down full . flush with the floor .
  3. Power steering problem

    Power steering problem

    hi shea , did you fit a new steering box or a second hand one . can you be sure the steering box you fitted is good
  4. Steering problem 8011(Please help)

    Steering problem 8011(Please help)

    hi shea . AFTER the pump theres a relief valve . it dumps into the power steering tank . you need to pressure test this , the relief valve can be adjusted from the bottom . . did you check filter. also the front unit under the rad could be bad . never had one open but am told its a nightmare...
  5. local irish vintage tractor run recent photos

    local irish vintage tractor run recent photos

    hi what year is your crystal.
  6. Zetor 12045

    Zetor 12045

    as dave said . i cant see how the back end oil can get into engine.
  7. Brakes bound 12145

    Brakes bound 12145

    you should be able to see the adjuster at the back. on the axle . some had two nuts there either 19mm or 22mm tip that back gently towards front of tractor . you could back of adjuster a bit. not to much or the cylinders will pop out . which i have done .. the cylinders could be a bit rough...
  8. URSUS 11054 - production started

    info URSUS 11054 - production started

    what are the specs of this tractor
  9. S

    question Long 910 tractor?

    it must be for the usa market.. . never heard of, or seen one before. very ugly tractor with that cab
    • sb
    • Post #4
    • Forum: Long
  10. S

    question Long 910 tractor?

    hi all whats the story behind this tractor. its a crystal running gear.
    • sb
    • Thread
    • Replies: 5
    • Forum: Long
  11. zetor 551 not firing on one cylinder

    zetor 551 not firing on one cylinder

    take the rocker cover of and have a look in . check the pushrods
  12. 16145 wont stay in second

    16145 wont stay in second

  13. 16145 wont stay in second

    16145 wont stay in second

    ya am wondering about that to . i had a 1224t with a torque multiplier . there seems to be a lot of torque multiplier parts aviable for 16045 and 16145 on the net.
  14. 5211 PTO shaft removal

    5211 PTO shaft removal

    hi gary were are you
  15. Next query: 6718 compressor

    Next query: 6718 compressor

    hi @Brian . i have seen a lot of zetors with the air hose run straight from the compressor . you could use a quick release of a air compressor make sure the centre is out . and then a quick release on your hose. make sure on the other end the part that goes onto tyre is straight threw. so the...
  16. 16145 wont stay in second

    16145 wont stay in second

    am after thinking the hole 4wd ratio could be out with that gearbox. your have to watch for that .
  17. 16145 wont stay in second

    16145 wont stay in second

    hi . if your going to use the hole back end of the 8011 . the first 8011 had different oil filters and housing . the later should have the same as yours . am not sure if the newer housing fits the older backend . also the 8011 backend had no oil cooler . but am sure you could make yours fit . am...
  18. zetor air compressor?

    zetor air compressor?

    the jockey wheel pulley that dave talks about .Should have a grease nipple in the centre . It sometimes gets so full of dirt that you dont see it.
  19. Engine stall

    Engine stall

    hi john if your in ireland conaty in kells should have .. the big question is why did the engine do this. is the rad blocked solid . was there coolant leak. is oil pump ok , etc
  20. Zetor Crystal 8011: sump gasket (coolant)

    Zetor Crystal 8011: sump gasket (coolant)

    i have seen some with the water sump bypassed join the inlet pipe and outlet pipe together.. say would be ok if tractor was not doing any hard work ,, but i would not take the risk
  21. Zetor Crystal 8011: sump gasket (coolant)

    Zetor Crystal 8011: sump gasket (coolant)

    hi yes there should be water down there, it helps to keep the sump oil cool . theres a m12, 17mm head bolt that will drain water out think its on right side . not on bottom on side .. your have to take that plate of and hope you can get studs out . you should be able to hammer out a gssket...
  22. Forterra 9641 lack off power

    Forterra 9641 lack off power

    hi renze our 9540 is a 35km . but to fair to the tractor it has a full set of weights on the front . full set of weights on the back rims and a quicky 430 loader fitted so say its pulling around a extra 1500kgs all the time. must stick it on a dyno tester just to see
  23. Forterra 9641 lack off power

    Forterra 9641 lack off power

    ya i have a 9540 to . i took pump of and got it recon and turned up . it still does not feel like a 95hp tractor . would take back my crystal in morning..
  24. Power steering on Zetor Crystal 8011?

    Power steering on Zetor Crystal 8011?

    hi thomas . the valve is on top of the power steering tank . i did turn this valve up using a pressure gauge .. i think the valve is metric thread .. i think it did not make the steering much lighter ...the front unit can be trouble sum.. i had a recon unit here only sold it a year ago on...
  25. Torgue amplifier 8111

    Torgue amplifier 8111

    hi am read this from the manual .. (pump tests) this may be perfomed when the floor has been partially removed by fixing the pressure gauge onto the gearbox cover supply tube end . the gauge for the test shall be provide with a thrrottle valve .. but if it was me i would stick in new pump ...
  26. Torgue amplifier 8111

    Torgue amplifier 8111

    i think dave has nailed it.. not sure if theres any point adjusting the valve under the floor panels . i no it has worked for me on the pto pack .. sure could be worth a try.. the valve contols the low pressure . dave should be able to tell you the correct pressure .. if you fit a new pump your...
  27. Torgue amplifier 8111

    Torgue amplifier 8111

    check backend oil level
  28. slow loader trip

    slow loader trip

    am i right in saying its slower to tilt out . that show be very fast as it has the weight helping it .. is it still slow with a heavy load.. has the loader check valve , soft ride , . i came across a problem something like yours . i tryed the cable ajustment with no joy.. it turned out it was...
  29. 16145 tranny swap

    16145 tranny swap

    here a rough idea.. most of the old gearboxes ran on r34 most were 30km.. and most gearboxes with the 3rd and 4th on the gear stick the wrong way round were either 35 or 40km alot of them ran on r38 . if the cab is still on shud be stamped on it some were
  30. torque specs 8011 pump

    torque specs 8011 pump

    hi as renze said use it as a door stopper.. you need to change the bush the shaft runs in or the seal will go agin.. i never seen the front seal going on pump .. are you sure the tractor hydraulic system is rite
Back
Top Bottom