• Hello Guest, you do not yet have the necessary rights to see the contents of our FAQ articles. Register in our forum, briefly introduce yourself and your Zetor in words and pictures and actively participate in discussions in the forum, then you will automatically receive access to the specialist articles in the FAQ.

Search results for query: *

  • Users: markty2
  • Content: Threads
  • Order by date
  1. Crystal lift problem

    Crystal lift problem

    Hi all, The lifts om my Crystal are playing up, I have no position control, i.e. lifts are either fully up or fully down. No middle ground. Also, when lifts are up, the relief valve is blowing off. I removed the lift cover & the 2 steel shock absorber plates mounted on the rear end of the...
  2. 8011 PTO noise ?

    8011 PTO noise ?

    Hi all, Just looking for a 2nd opinion before I go splitting my 8011. It is making a groaning noise when the PTO is turned on, and whenever the PTO comes under a heavy load. Also a vibration can be felt through the floor, just under your feet, at the same time. I have a feeling that it might...
  3. 12011 cylinder head

    12011 cylinder head

    Hi all, Just wondering if anyone can tell me if the valve seat inserts for a 12111 head can be used in a 12011 head. Some of my valve seats are worn & it would be cheaper to buy the ready to fit inserts than to get them made from scratch. Was there any difference in valve size, seating angles...
  4. 8011 injector pump settings

    8011 injector pump settings

    Hi all, Has anybody got any experience adjusting the amount of fuel being delivered by the injector pump ? I think my 8011 is a tad overfuelled & I would like to try to turn it back a little. It has a 2478 pump & the spill timing has been checked & is spot on. I have tried adjusting the...
  5. 6341 fuses

    6341 fuses

    Anyone have any idea if the spotlights & headlights are fused on a 2004 6341 super. I have tried all the fuses behind the dashboard side panel but they are Ok. Are there fuses hidden somewhere else ? Thanks Mark
  6. 8011 steering

    8011 steering

    Hi all, My steering has developed a strange fault & I'm hoping that somebody can help me figure it out. It is very heavy when turning left, but works fine when turning right. Oil level is OK , and I have changed the valve at the end of the steering piston (behind the end plate ) for a known...
  7. 8011 PTO HP

    8011 PTO HP

    Hi All, Just wondering what the correct PTO HP for a 1978/79 8011 is ? I have 2 Crystals with exactly the same engine (8001) & the same injector pump (2478 ) & I put both of them on a Dyno tester today (see video on YouTube ;)) and there is a massive difference between the two tractors. My...
  8. 6341 High/Low range ?

    6341 High/Low range ?

    Hi All, Has anyone got a parts diagram for the high/low range lever and selector for a 2004 6341 ? A friend of mine is having difficulty engaging the low range on his tractor. I had a look at it today & the lever is working OK outside the gearbox housing & I was wondering if the 6341 has a...
  9. Connections for tail lamps

    Connections for tail lamps

    Hi All, Does anyone know if the fibre connector holders/ bulb holders can still be got for the lights used on later 8011 models ( I think they were also used on the "0" & "2" series models. Thanks. Mark
  10. URGENT !! Crystal tappet settings.

    URGENT !! Crystal tappet settings.

    Hi everyone. Looking for the valve clearance settings for a Zetor 8001 engine A.S.A.P. Thanks. Mark.
  11. Original parts for 8011 ?

    Original parts for 8011 ?

    Hi, Has anybody got good leads on where to get original parts for a Crystal ? Have decided to tidy up my new arrival a bit ;D I would like to keep it as near to original as I can so I am looking for the following bits , 1. Enamel exhaust with short top pipe & take off for air filter...
  12. More Crystal questions ??

    More Crystal questions ??

    Hi again, My 8011 has a pretty bad oil leak coming from the joint between the gearbox & the back of the bellhousing. It is back end oil that is leaking. The leak seems to be worse when the tractor is not running. I have tried parking the tractor with the front end elevated but it still leaks...
  13. 8011 diesel troubles.

    8011 diesel troubles.

    Hi all , My 8011 has a bit of a problem & I was wondering if anyone can shed a little light on a fix for it. If left overnight , when you try to start it , it seems that the diesel has run back towards the tank. The tractor will start, but it splutters for about 5 - 10 seconds & then clears...
  14. 8011 Roof

    8011 Roof

    Just wondering if anyone knows if a new roof can be got for a standard Zetor cab as fitted to 8011 etc. Or if any of the Irish forum members have a usable second - hand one lying around this would be great too. Just after buying a 1978 8011, a tractor I have wanted for a very long time & I...
  15. Oil from engine breather, How serious ?

    Oil from engine breather, How serious ?

    Hi All, I have recently bought a 6718, and it is leaking oil from the Banjo fitting on the side of the block, where the breather hose is connected to. The engine starts no problem, and sounds very sweet, and has lots of power. The tractor has been almost totally idle for approx 18 months...
  16. Hello again & Clutch question ?

    Hello again & Clutch question ?

    Hi everyone, I have just signed up again, as I can't log in using my old user name ? Anyway, I am doing a clutch in a 5611 and I need to know what the finger settings are ? It is using one release bearing to operate both the travel/main clutch and the PTO clutch, as opposed to the dual...
  17. Zetor 5501 engine settings.

    Zetor 5501 engine settings.

    Hello I am just in the middle of an engine rebuild on my 5611 ( pistons, liners etc.) Hoping someone has some information on tightening torques for big end bearings, cylinder head etc. also valve clearances. Thanks. Mark
  18. Help with Logo for 5611

    Help with Logo for 5611

    Hi Hoping that somebody can help me. I am looking for a close up photo of the script on the bonnet side panel. It is badly faded on my 5611 and even though it can still be read I cannot make out what the correct colour is. Thanks Mark
Back
Top Bottom