• Hello Guest, you do not yet have the necessary rights to see the contents of our FAQ articles. Register in our forum, briefly introduce yourself and your Zetor in words and pictures and actively participate in discussions in the forum, then you will automatically receive access to the specialist articles in the FAQ.

Recent content by tagew

  1. 6341 no power

    6341 no power

    Yes, it was the front brakes. Some problem in air assisted headcylinder for frontbrakes, there was a lot of rust in headcylinder so I have to change it to a new one and air cylinder was also hard to move and the hole who let leaking air was full of dirt so air pressure go to brake fluid...
  2. More fuel to 6341

    More fuel to 6341

    Hello, if I want to give my 6341 a little more fuel, where can I adjust? Do I need to remove coverplate at the end of the pump? Anyone who have pictures or some more information about that type of injection pump? Br Tage W.
  3. 6341 no power

    6341 no power

    Yes, I have also thinking about that with front brakes but after a while with driving it is not warm at all when I put my hand on it, should it not be warm if it was a problem there. Im am thinking more on some fuel problem common for all cylinders because engine is running fine so I dont think...
  4. 6341 no power

    6341 no power

    Hello, I have a 6341 from year -98 with 2150 hours on meter and it has very low power, specially when it is cold. Sometimes it is so low so it is nearly cant run on 5 gear with empty tractor. Sometimes it would be better after a while and sometimes not. I have replaced the fuelfilter but it did...
  5. Need Advise on repair 6320

    Need Advise on repair 6320

    This is maybe an answer mostly to Hazze but of course anyone can use this information. You can call or send mail to Motocheck in swedish part of Finland. You can use swedish or maybe also english, he can make delivery of spareparts and he also know a lot of Zetor and problems that the there can...
  6. Hourmeter on 5245

    Hourmeter on 5245

    Hello, I have a friend who have problem with the hourmeter on his 5245 from year 1988. The tachometer is working but not the hourmeter. He has also changed the whole instrument but the result was the same??? Does anyone know anything about this problem or know where to find a good electrical...
  7. Hydraulic problem 6341

    Hydraulic problem 6341

    Hello, I have a hydraulic problem on my 6341. When I have something little heavier in my lift arms they will drop down a little bit and after about 10 sek they go up and so on, down - up - down - up..... I have changed the seals in master lift cylinder and also changed the hydraulic valve bloc...
  8. Hudraulic will not lift to top

    Hudraulic will not lift to top

    Ok, I will send you the pictures in a few days, now Im at work and I dont know if I can do it in the evening. Ill send them at your e-mail. I cant say if it are the same on 6245, my tractor are a 6341 and when I had 6245, I didnt need to do this job. I had to remove the seat, the rubber floor...
  9. Hudraulic will not lift to top

    Hudraulic will not lift to top

    Now the problem are fixed:-) It was the "stopping screw", a 6 mm bolt about 15 - 20 mm length. There was only about one and a half turn, then it should dropped down into rear axle and what had happen if it had I dont know. Now I put on a little "Loctite" when I put the bolt back and after...
  10. Hudraulic will not lift to top

    Hudraulic will not lift to top

    Thanks Renze, but on the 6341 thera are links between the levers and the axle into the body so it is easy to loose those links. I talked to Bengt-Erik on Moto Check today and he said the problem was a "stopping screw" on the valve. Sometimes that screw falls down to the hydraulic pump and he has...
  11. Hudraulic will not lift to top

    Hudraulic will not lift to top

    Yes Renze, I also was thinking of something like that. I havent ever done a job like this on Zetor but one time I changed an wheel in the gearbox of a Valmet 361. Does the cylinder and everything comes with the cover if I take that away, I mean is that a part of its own so I can take it away an...
  12. Hudraulic will not lift to top

    Hudraulic will not lift to top

    Hello again, it was not anything with temperature because it was the same problem this morning in warmgarage. I also removed the links wich go to the lever in cabin so I could rotate the axle into the body "free". It isnt possible to rotate the axle more than the lever can do in those space. The...
  13. Hudraulic will not lift to top

    Hudraulic will not lift to top

    Thank you Hogi, sorry but I cant speak and understand finnish, only swedish and a little bit of english. It would be nice to understand finnish but I can only a few words, I was reading finnish only one year at school for about 33 years ago. "[b]If you continue using hydraulics soon your first...
  14. Hudraulic will not lift to top

    Hudraulic will not lift to top

    I can lift the arms to its upper level by hand so they are not blocked mecanically. Now I have the tractor in a warmgarage in +12 and will see tomorrow what happend. The lever is working properly and the links looking good but when I put the lever to down position I have about 2 inch to put down...
  15. Hudraulic will not lift to top

    Hudraulic will not lift to top

    Ok, I have to explain a little bit more if I found the right words, my english are not so good. On my earlier 6245 and also on my 6341 there will be when I take the lever up, the last little bit (about 1 inch) on the lever will give a little bit faster liftning of hydraulic arms for the last...
See more
Back
Top Bottom