• Hello Guest, you do not yet have the necessary rights to see the contents of our FAQ articles. Register in our forum, briefly introduce yourself and your Zetor in words and pictures and actively participate in discussions in the forum, then you will automatically receive access to the specialist articles in the FAQ.

Recent content by prestonpaul

  1. Hydrostatic steering kit

    Hydrostatic steering kit

    Ive had problems with the steering of my 6245 for as long as I have had it. Yesterday I broke the rod end that connects to the steering cylinder and now have no steering at all. Instead of spending a lot of money reconditioning the steering and still have mediocre power assisted steering I am...
  2. Introduction & Request for help on 4911 hydraulic problems

    Introduction & Request for help on 4911 hydraulic problems

    Mine does the same thing. I am on the verge of ordering replacement parts (inner circuit control linkage and the rod it pivots on) to see if that rectifies the problem. keep us posted with how you go. Paul.
  3. 8011 zetor

    8011 zetor

    I used the oil drain hole on the rear axle of my 6245 for the return line of the loader and took the pressure from the plug on the pump plate on the bottom of the rear axle as well. You have to have the remote lever locked either fully forward or backward to get pressure at that point, but it...
  4. Introduction & Request for help on 4911 hydraulic problems

    Introduction & Request for help on 4911 hydraulic problems

    In my limited experience with my 6245, I have had the following issues: There is a pipe that runs through the diff housing between the pump plate and the top housing, this is sealed with o rings, mine got old and brittle and failed causing a loss of pressure. My lift cylinder seals were damaged...
  5. Introduction & Request for help on 4911 hydraulic problems

    Introduction & Request for help on 4911 hydraulic problems

    Just don't pay for it ;D Sounds like you are having similar issues to me with my 6245. I have yet to get mine sorted out but have found a few other problems along the way. I'm at work now but I'll post some suggestions when I get home.
  6. Need Advise on repair 6320

    Need Advise on repair 6320

    [url=http://www.website.com]http://www.ibeno.cz/ukindex.htm[/]
  7. Need Advise on repair 6320

    Need Advise on repair 6320

    I think I would be going somewhere other than the dealer! It's not a warranty issue so anyone can do the job. Perhaps ask around locally for a mobile tractor mechanic that will visit you? I suspect the brake issue will be hydraulic as well, if it reoccurs replace the master cylinders and think...
  8. Zetor 6441 top link on 3pt question

    Zetor 6441 top link on 3pt question

    I had the same issue on my 6245 when I bought it. I just filed enough off the flanges of the ball on one end of a Bareco top link so it would fit. In my case the very top hole for the pin is cat 2 on one side and cat 1 on the other which is a bit odd, all the holes below are cat 2. Hope that...
  9. Inner circuit spool valve

    Inner circuit spool valve

    I did see that, but couldn't see how it adjusted as there didn't appear to be a slot to alow for movement. I'll have another look though, thanks. I also tried taking the lever off the shaft to rotate it on the spline, but the spline is indexed so no joy there. Give it a couple of weeks untill I...
  10. Inner circuit spool valve

    Inner circuit spool valve

    The whole manual is like that, but once you actually have a go with the tractor in front of you, it's not too bad.
  11. Inner circuit spool valve

    Inner circuit spool valve

    Tried both those things. It's amazing how complicated the manual makes a simple procedure sound! I got a little more travel but when I put the quadrant lever cover back on what I gained was lost as it limits the travel of the inner circuit leaver somewhat. Thanks for the suggestions though, keep...
  12. Inner circuit spool valve

    Inner circuit spool valve

    I wish it were that simple, but in my case unfortunately not. I am not getting full travel at the upper arms, probably only about half to two thirds. Definately something wrong with the hydraulic distributor or the mechanism that controls it. I did find what looks like a steel pin or plug of...
  13. Inner circuit spool valve

    Inner circuit spool valve

    Bump Thoughts anyone?
  14. Differential lock pedal

    Differential lock pedal

    Down is engaged on my 6245.
  15. Inner circuit spool valve

    Inner circuit spool valve

    Yes there is a spring between the two halves. To give you a bit of back ground, the tpl has never worked correctly on this tractor. When I bought it, there was no controll at all, so I removed the hydraulic cover and replaced all the o-rings in the hydraulic distributor and the seals in both...
See more
Back
Top Bottom