• Hello Guest, you do not yet have the necessary rights to see the contents of our FAQ articles. Register in our forum, briefly introduce yourself and your Zetor in words and pictures and actively participate in discussions in the forum, then you will automatically receive access to the specialist articles in the FAQ.

Recent content by paul_walpole

  1. 5211 Hard Starting

    Hello Mike, I have had issues with my 7245 since I bought it new in 1989. It has always had issues if let sit for a while. I belive it is in the pump letting the pressure bipass in some way or another but fuel line, non-return valve, filters and evrything else never seen to work. In the end, I...
  2. 7745 hard to steer

    I don't think much of your zetor dealer if he didn't spot the ram actuator out of centre ballance.
  3. More problems than bleeding the brake fluid!

    It is good to see you have followed the advice from all of us and are now mobile again. You will now know what I meant by one of the selectors being out. Did you find the source of the brake fluid leak. Paul
  4. 5211 clutch bleed valve location????

    Thats interesting, on my 7245, it is on the right hand side, under the fuel tank so to speek.
  5. More problems than bleeding the brake fluid!

    Hello there, If the tractor will go into reverse and there is no brake bind, then problem is in the selectors in the top of the box. You see sometime the selectror shaft gets out of the 3 selector races, especially if the gear shift is getting sloppy or it is forced. With low clutch fluid, it...
  6. Zetor 9520

    I have a 9540 witch is the FWA equivalent. I have done over 5000 hrs and other than the air conditioning have not had an issue. Hang on, I had some selector problems under warrently. Common problem but would be fixed on any tractors with the same problem by now. It have very honest power, rated...
  7. 3545 battery

    My experience is fit the largest physical one that will fit comfortably into the box. No less that 680 CCA, preferably higher
  8. 4712

    I have a headacke
  9. 4712

    I also am at the age where I started learning imperial then changed to metric. With water, I generally express in PSI due to the incriments being smaller. The nozzells on the srays are also spec with litres per minute at PSI figures. And that are from Europe. Go figure? Paul
  10. Hydraulics - New PUMP?

    If its a Burder loader, the same as mine I am assuming you are also in OZ. Wher abouts??
  11. 4712

    The 3/4 Harland is an irrigation pump. At the speed mentioned it is pumping 600 litres per minute at 45PSI, 500 meters through a 25mm big gun travelling irrigator.
  12. 4712

    A little bit of trivia for you all. I have two 4712. One a 1970 and the other 1971. They have 22000 ans 19000 hrs respecively. The younger one is pumping a 3/4 harland as we speak, at 1500 RPM, 540 PTO with a watchdog system The older unit has had one clutch, under warrently from new and a...
  13. Hydraulics - New PUMP?

    Ok, the plot thickens. The fact that the pump has been changed tells you all will be ok there so as suggested, either relief valve is below the specified pressure. the reason the loader lifts in 1000 PTO is that the relief buils pressure behind it with the higher oil flow sending higher pressure...
  14. Engage a PTO on Zetor 6211

    Hey all, I am in Australia with the PTO clutch leave to the left of the seat, rear facing oppisite to the hanbrake leaver. PTO enguage on the floor slightly to the left of centre, All the way forward / down for 0 PTO. Ist notch up for revs enguage. Second notch for neutral and thurd notch for...
  15. Zetor gearoil

    In Australia, only 80/90 is recomended. I have over 30000 hrs combined in my 3 units running the same, no drama's
Back
Top Bottom