• Hello Guest, you do not yet have the necessary rights to see the contents of our FAQ articles. Register in our forum, briefly introduce yourself and your Zetor in words and pictures and actively participate in discussions in the forum, then you will automatically receive access to the specialist articles in the FAQ.

Recent content by jex

  1. Zetor 6045 slow response to throttle

    question Zetor 6045 slow response to throttle

    When removing the.injector pump, do any procedures need to be followed to ensure the timing is correct.when reinstalling. According to the workshop manual there is no timing process mentioned other than Mark the position of the case where it bolts to the compressor ?
  2. Zetor 6045 slow response to throttle

    question Zetor 6045 slow response to throttle

    I was referring to this access point on the front of the pump.
  3. Zetor 6045 slow response to throttle

    question Zetor 6045 slow response to throttle

    Thankyou Joachim, I'm in Australia so repair could be an issue here. I contacted Zetor in CZ regarding a replacement pump 2 weeks ago by email but they have not replied? What is the function of the " Fuel adding device ZS10-969" on the front of the pump? I was wondering if I could utilise that...
  4. Zetor 6045 slow response to throttle

    question Zetor 6045 slow response to throttle

    Finally have time to have another go at getting the old girl going again before the summer starts in Oz. I still have had no luck in getting it to start. Checked oil levels in the pump and the starter spins over fast enough. I don't seem to be getting any fuel at the injectors so I assume the...
  5. Zetor 6045 slow response to throttle

    question Zetor 6045 slow response to throttle

    Fuel flow from the tank is good
  6. Zetor 6045 slow response to throttle

    question Zetor 6045 slow response to throttle

    Thankyou. Where is the regulator situated and how is the oil checked / changed? It maintains the revs but when the throttle is dropped back to idle, it slowly responds and almost stops unless I increase it again.
  7. Zetor 6045 slow response to throttle

    question Zetor 6045 slow response to throttle

    I recently had a problem with my 6045 not starting. I thought it was a faulty lift pump so I replaced it with a new pump & new fuel filters. After bleeding the injectors I got it to start eventually but the it is very slow to respond to the throttle control. Could this be an issue with the...
  8. 6045 steering ram needed in Oz

    6045 steering ram needed in Oz

    I have spoken to a zetor dealer in Oz and the zetor part is over $1000 in Oz.
  9. 6045 steering ram needed in Oz

    6045 steering ram needed in Oz

    Hi Guys, I'm chasing a steering ram for a 6045 in reasonable condition in Australia. Please PM me if you can help with information on where I might find one. Same ram fits the following models 3320, 3340, 4320, 4340, 4911, 5011, 5211, 5245, 5320, 5340, 5340H, 5511, 5611, 5711, 5718, 5745, 5748...
  10. 8045 slasher operation

    8045 slasher operation

    Ok, thanks mate, I'll have a play with the adjustments. I thought I may have had an incorrect setting on the controls.
  11. 8045 slasher operation

    8045 slasher operation

    I have dropped the hitch as far as it will go but the slasher still comes of the ground when going over a rise
  12. 8045 slasher operation

    8045 slasher operation

    I still have not figured out how to adjust the 3 point linkage controls on my 8045 to get my slasher to follow the contour of the ground I am slashing. Is there some way of overiding the automatic leveling function so the slasher will follow the land contour?
  13. has anyone converted an FEL bucket to a 4 in 1 bucket ?

    has anyone converted an FEL bucket to a 4 in 1 bucket ?

    Thanks for the reply. The grapple idea seems to be a good option. I would like the option of being able to pull & pick up brush, trees etc. I currently spend a lot of time jumping in & out of the tractor using a chain to do this function. Another use for the 4 in 1 would be in spreading and...
  14. has anyone converted an FEL bucket to a 4 in 1 bucket ?

    has anyone converted an FEL bucket to a 4 in 1 bucket ?

    I have a 6045 with an FEL. There are times when it would be handy if the bucket was a 4 in 1. Has anyone done this conversion if it is possible ?
  15. Paint colours for 6045 in Australia

    Paint colours for 6045 in Australia

    Thanks for the replies guys. I ended up getting the local Wattyl dealer to mix the Zetor red in Ag enamel, used the wattyl dark green & white for the wheels. I had a mate sandblast all the parts( last friday)and had to make a quick decision as there was rain on the horizon. As it turned out it...
See more
Back
Top Bottom